- Russian (Русский)
- Bulgarian (Български)
- Chinese Simplified (简体中文)
- Chinese Traditional (繁體中文)
- Czech (Čeština)
- Danish (Dansk)
- Dutch (Nederlands)
- Estonian (Eesti)
- French (Français)
- German (Deutsch)
- Greek (Ελληνικά)
- Hungarian (Magyar)
- Italian (Italiano)
- Japanese (日本語)
- Korean (한국어)
- Polish (Polski)
- Portuguese (Brazilian) (Português (Brasil))
- Slovak (Slovenský)
- Spanish (Español)
- Swedish (Svenska)
- Turkish (Türkçe)
- Ukrainian (Українська)
- Vietnamese (Tiếng Việt)
Scanning isn't the only way to acquire images of your documents. You can recognize photos of documents taken with a camera or a mobile phone. Simply take a picture of text, save it to your hard disk, and open it in ABBYY FineReader.
When taking pictures of documents, a number of factors should be kept in mind to make the photo better suited for recognition. These factors are described in detail in the sections that follow:
Your camera should meet the following requirements in order to obtain document images that can be reliably recognized.
Recommended camera characteristics
- Image sensor: 5 million pixels for A4 pages. Smaller sensors may be sufficient for taking pictures of smaller documents such as business cards.
- Flash disable feature
- Manual aperture control, i.e. availability of Av or full manual mode
- Manual focusing
- An anti-shake system or ability to use a tripod
- Optical zoom
- 2 million pixels for A4 pages.
- Variable focal distance.
Note: For detailed information about your camera, please refer to the documentation supplied with your device.
Lighting greatly affects the quality of the resulting photo.
Best results can be achieved with bright and evenly distributed light, preferably daylight. On a bright sunny day, you can increase the aperture number to get a sharper picture.
Using a flash and additional lighting sources
- When using artificial lighting, use two light sources positioned so as to avoid shadows or glare.
- If there is enough light, turn the flash off to prevent sharp highlights and shadows. When using the flash in poor lighting conditions, be sure to take photos from a distance of approximately 50 cm.
Important! The flash must not be used to take pictures of documents printed on glossy paper. Compare an image with glare and a good quality image:
If the image is too dark
- Set a lower aperture value to open up the aperture.
- Set a higher ISO value.
- Use manual focus, as automatic focus may fail in poor lighting conditions.
Compare an image that is too dark with a good quality image:
To obtain good quality photos of documents, be sure to position the camera correctly and follow these simple recommendations.
- Use a tripod whenever possible.
- The lens should be positioned parallel to the page. The distance between the camera and the document should be selected so that the entire page fits within the frame when you zoom in. In most cases this distance will be between 50 and 60 cm.
- Even out the paper document or book pages (especially in the case of thick books). The text lines should not be skewed by more than 20 degrees, otherwise the text may not be converted properly.
- To get sharper images, focus on the center of the image.
- Enable the anti-shake system, as longer exposures in poor lighting conditions may cause blur.
- Use the automatic shutter release feature. This will prevent the camera from moving when you press the shutter release button. The use of automatic shutter release is recommended even if you use a tripod.
- the image is too dark or its contrast is too low.
Solution: Try to improve the lighting. If that is not an option, try setting a lower aperture value.
- the image is not sharp enough.
Solution: Autofocus may not work properly in poor lighting or when taking pictures from a close distance. Try using brighter lighting. Use a tripod and self-timer to avoid moving the camera when taking the picture.
If the image is only slightly blurred, try the Photo Correction tool that is available in the Image Editor. For more information, see "Editing Images Manually."
- a part of the image is not sharp enough.
Solution: Try setting a higher aperture value. Take pictures from a greater distance at maximum optical zoom. Focus on a point between the center and the edge of the image.
- the flash causes glare.
Solution: Turn off the flash or try using other light sources and increasing the distance between the camera and the document.
11/2/2018 5:31:18 PM